[SOLVED] Throttle off in Diagnostics

In case you do not know something or you are not sure, here is the right place for your question.
Post Reply
Bladetip
Posts: 46
Joined: Thu 17. Mar 2016 5:06:21

Ok I have bailout set up with my DX8, swash moves upon activation as its supposed to. My next question is in diagnostics tab, my throttle is at 4%. and only goes to 98%.
These settings I had already zeroed out and had them set correctly but now they are off. My question is do I correct this? If so how? and where do I go in the DX8 to do this I cannot remember where I went into the radio to adjust this! :-(

Also what mode of rescue should I be in normal? or Acro? What is the difference? Forgive me but it's been a while since I had originally set this up, and I have forgotten....
Top
jgiannakas
Posts: 183
Joined: Sat 02. Jan 2016 12:17:50

Rescue Normal always rescues to upright, even if you are inverted. Rescue acro rescues to the nearest orientation, so if you're inverted or close to inverted it will level inverted and punch out.
Top
Adrian
Posts: 204
Joined: Thu 08. Oct 2015 14:43:12
Location: Switzerland

Tab on the wheel on you DX8 / Select Servo Setup / Travel Throttle
Make sure your at Motor OFF position, adjust left 100% likely to 102% for Lower value
Go to full and adjust right 100% likely to 102% for upper Value.
Monitor it in Diagnostics.
Oxy4max SpiritPro + HW // SOXOS 550, SpiritPro, HW120A V4, 920KV // SOXOS 600, SpiritPro, HW160A, Pyro650 // SOXOS Strike7, SpiritPro, HW160A, Pyro750 // Skywing Spirit Aero // FrSky Horus X10S + Taranis X7 /
Top
Bladetip
Posts: 46
Joined: Thu 17. Mar 2016 5:06:21

Great thank you very much! Oh I am running governor will I need to readjust anything?
Top
jgiannakas
Posts: 183
Joined: Sat 02. Jan 2016 12:17:50

Bladetip wrote:Great thank you very much! Oh I am running governor will I need to readjust anything?
Yes you would but what exactly depends on your ESC. What brand are you using?
Top
Bladetip
Posts: 46
Joined: Thu 17. Mar 2016 5:06:21

It's a Hobby Wing pLatinum Pro 100a
Top
jgiannakas
Posts: 183
Joined: Sat 02. Jan 2016 12:17:50

Bladetip wrote:It's a Hobby Wing pLatinum Pro 100a
Ok perfect you'll need to recalibrate the ESC to the new settings.

Disable the governor, power on your TX, put a linear throttle curve 0-100, put throttle stick on high, power model on, wait for the two beeps, put stick to low, wait for the ESC to initialise, unplug everything, reactivate gov and set a flat TC. Done!
Top
Bladetip
Posts: 46
Joined: Thu 17. Mar 2016 5:06:21

Great sounds good thanks so much!
Top
User avatar
Coco66
Posts: 433
Joined: Sun 26. Jul 2015 8:17:50
Location: Madrid, Spain / Torino, Italy

jgiannakas wrote:Disable the governor, power on your TX, put a linear throttle curve 0-100, put throttle stick on high, power model on, wait for the two beeps, put stick to low, wait for the ESC to initialise, unplug everything, reactivate gov and set a flat TC. Done!
A perfect write up! Well done! Never seen it explained which such a short paragraph.
Oxy 2 ♦ X-Vert ♦ Warp 360 ♦ Blade 450X ♦ Blade 450X Nightflyer ♦ Goblin 500 (RIP) ♦ 2 X mCPX v2 ♦ night fly mQX ♦ LadyMQX ♦ nano QX ♦ nano QX FPV ♦ Inductrix ♦ DX8 G1
Top
jgiannakas
Posts: 183
Joined: Sat 02. Jan 2016 12:17:50

Coco66 wrote:
jgiannakas wrote:Disable the governor, power on your TX, put a linear throttle curve 0-100, put throttle stick on high, power model on, wait for the two beeps, put stick to low, wait for the ESC to initialise, unplug everything, reactivate gov and set a flat TC. Done!
A perfect write up! Well done! Never seen it explained which such a short paragraph.
Haha thank you! That's what happens when you type in responses right before going to work and you're in a bit of a rush [emoji39][emoji39][emoji39]
Top
Post Reply

Return to “Support”