Perfect! Thanks for screenshot.
Now it is OK. It was rather only cosmetical issue, because throttle signal is not passed to the ESC at all in case your TX was off before the unit was on.
Servo's go crazy when saving unit
Spirit System developer
Ahh cool.. No probs..
I am still running my throttle cable from the RX (per 1.24) and can't be bothered rewiring it!!
Lets see how Jmann goes with his save testing..
Now you can wrap it up for afternoon!!
Oh & is it ok to fly with test23??
While you're here..
A quick question that I have been thinking about.
I have finally sorted out a problem, with my pitch setting.
You may have noticed that in some of the screen shot's my pitch 0 value was actually 7.
I have fixed this by changing the PPM center value in OpenTX from the standard of 1500 to 1545.
Any thoughts?
Cheers,
Yak.
I am still running my throttle cable from the RX (per 1.24) and can't be bothered rewiring it!!
Lets see how Jmann goes with his save testing..
Now you can wrap it up for afternoon!!
Oh & is it ok to fly with test23??
While you're here..
A quick question that I have been thinking about.
I have finally sorted out a problem, with my pitch setting.
You may have noticed that in some of the screen shot's my pitch 0 value was actually 7.
I have fixed this by changing the PPM center value in OpenTX from the standard of 1500 to 1545.
Any thoughts?
Cheers,
Yak.
Yes, you can fly with test23 without any problem.
Changing center pulse for collective channel is OK and correct. There are differences across all the tranmitters and receivers.
Changing center pulse for collective channel is OK and correct. There are differences across all the tranmitters and receivers.
Spirit System developer
Test 23:
- No issue opening log or saving.
- When Tx is powered off and heli is either not plugged into computer or plugged in, heli does fast twitching on all servos until link is restored.
My Failsafes are set to "No pulse" in Open Tx
My Pitch center is 1500us as I changed the subtrim instead... In Servo tab It is set to 6 on the subtrim with the max limit at 89 and min limit at -77
- No issue opening log or saving.
- When Tx is powered off and heli is either not plugged into computer or plugged in, heli does fast twitching on all servos until link is restored.
My Failsafes are set to "No pulse" in Open Tx
My Pitch center is 1500us as I changed the subtrim instead... In Servo tab It is set to 6 on the subtrim with the max limit at 89 and min limit at -77
Hmm, thanks.
Could you change your failsafe settings? At least for throttle channel? I believe it could fix the problem.
Could you change your failsafe settings? At least for throttle channel? I believe it could fix the problem.
Spirit System developer
You are quite correct.
When I set the failsafe values in Open tx to Custom and just put channel 3 (Throttle) to -100 It displays no issues.
Very weird.
However, it also activates rescue. Not sure if that is a good or a bad thing. Could be nice if I loose signal but it will also cut throttle so may cause more damage. I think I just have to adjust channel 5 to be a positive value when failsafes go on.
When I set the failsafe values in Open tx to Custom and just put channel 3 (Throttle) to -100 It displays no issues.
Very weird.
However, it also activates rescue. Not sure if that is a good or a bad thing. Could be nice if I loose signal but it will also cut throttle so may cause more damage. I think I just have to adjust channel 5 to be a positive value when failsafes go on.
Thats because failsafe does not worked at all with Tarantis with 1.0.25 
Spirit System developer