Need higher tail gain at higher rpm??
Posted: Wed 26. Apr 2017 14:49:22
Hi,
I`m having difficulties comprehending what is wrong with my setup as I need conciderably higer tail gain when I go from normal at 2470 rpm headspeed to Idleup 1 at 2680 rpm.
My setup is as follows:
Devil 380
Spirit Pro
Hobbywing Platinum 80 V4
Alzrc DS501MG tail servo at 7.4V
●Operating Voltage:DC6.0V-8.4V
●Working frequency:1520us/333Hz 800us-2200us
●Speed and torque:
- 6.5Kg.cm/0.05sec/60°@8.4V
- 5.5Kg.cm/0.06sec/60°@7.4V
- 4.6Kg.cm/0.07sec/60°@6.0V
I use the Spirit governor, and has it set in a manner that gives no bogging at pitch pumps (+/- 11.5)
Have changed main pinion to 19 tooth and tail pinion to 19 tooth as well due to running quite low headspeeds.
The enclosed profile settings of Normal and Idleup 1 is what I ended todasy flying with.
Normal mode is holding tail almost perfectly with 75% gain and 1.22 common tail gain when pitch pumping.
Idleup 1 is kicking about 5 degrees at 100% gain and 1.50 common gain when pitch pumping.
What am I missing here? Shouldent it be the other way around- more rpms=less tail gain if all else is equal?
I have looked at my setup time and time again, and cannot find any reason for this behavior.
I do not have a reamer for the ball links, but the tail is running quite smooth. The lenght from servo center to link is 13mm, so dead center as per assembly manual. Fyi I have also tried at 11mm and 14mm with same results.
Edit: I have full travel in each direction on the tail.
Any help is appreciated.
Brgds
Stefan
I`m having difficulties comprehending what is wrong with my setup as I need conciderably higer tail gain when I go from normal at 2470 rpm headspeed to Idleup 1 at 2680 rpm.
My setup is as follows:
Devil 380
Spirit Pro
Hobbywing Platinum 80 V4
Alzrc DS501MG tail servo at 7.4V
●Operating Voltage:DC6.0V-8.4V
●Working frequency:1520us/333Hz 800us-2200us
●Speed and torque:
- 6.5Kg.cm/0.05sec/60°@8.4V
- 5.5Kg.cm/0.06sec/60°@7.4V
- 4.6Kg.cm/0.07sec/60°@6.0V
I use the Spirit governor, and has it set in a manner that gives no bogging at pitch pumps (+/- 11.5)
Have changed main pinion to 19 tooth and tail pinion to 19 tooth as well due to running quite low headspeeds.
The enclosed profile settings of Normal and Idleup 1 is what I ended todasy flying with.
Normal mode is holding tail almost perfectly with 75% gain and 1.22 common tail gain when pitch pumping.
Idleup 1 is kicking about 5 degrees at 100% gain and 1.50 common gain when pitch pumping.
What am I missing here? Shouldent it be the other way around- more rpms=less tail gain if all else is equal?
I have looked at my setup time and time again, and cannot find any reason for this behavior.
I do not have a reamer for the ball links, but the tail is running quite smooth. The lenght from servo center to link is 13mm, so dead center as per assembly manual. Fyi I have also tried at 11mm and 14mm with same results.
Edit: I have full travel in each direction on the tail.
Any help is appreciated.
Brgds
Stefan