Spirit unit + Graupner MX-20 + Graupner GR-16 + UniSens-E

In case you do not know something or you are not sure, here is the right place for your question.
Post Reply
pidder
Posts: 5
Joined: Mon 24. Jun 2019 9:47:02

Hi, my question is regarding the above metioned setup.

I use UniSens-E (under Graupner HOTT as GAM)to detect the used capacity and let the receiver tell me by using a switch.
Now - with the sprirt unit i have to decide whether i will use telemetry port for spirit setup or to use the UniSens-E unit.

My question: Is there any possible wireing to have both functions possible via the telemtry port? :?

regards
Peter
Top
TomasN
Posts: 261
Joined: Sun 23. Mar 2014 12:13:16
Location: Černošice/Praha

Yes, you can use Y-cable. But before connecting of both components you have to set UnisensE or Spirit to EAM mode instead of GAM.
TDF, TDR, Logo 600SX, Oxy 4 Max @ 3Digi, VBar Neo, Spirit, Grapuner mz-32, mx-20
Top
TomasN
Posts: 261
Joined: Sun 23. Mar 2014 12:13:16
Location: Černošice/Praha

See http://manual.spirit-system.com/index.p ... _Emulation how to change sensor emulation mode for Spirit
TDF, TDR, Logo 600SX, Oxy 4 Max @ 3Digi, VBar Neo, Spirit, Grapuner mz-32, mx-20
Top
pidder
Posts: 5
Joined: Mon 24. Jun 2019 9:47:02

TomasN wrote:See http://manual.spirit-system.com/index.p ... _Emulation how to change sensor emulation mode for Spirit
this - i will try this - but what about the wires?
The unisons needs the red cable for power-supply. It is recommended that on the SYS-port of the spirit the must not be any voltage!!!

Did you cut the red wire or is it no problem?
Top
TomasN
Posts: 261
Joined: Sun 23. Mar 2014 12:13:16
Location: Černošice/Praha

Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable.
wiring.png
wiring.png (11.38 KiB) Viewed 1438 times
Last edited by TomasN on Thu 04. Jul 2019 20:23:59, edited 1 time in total.
TDF, TDR, Logo 600SX, Oxy 4 Max @ 3Digi, VBar Neo, Spirit, Grapuner mz-32, mx-20
Top
pidder
Posts: 5
Joined: Mon 24. Jun 2019 9:47:02

TomasN wrote:Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable.
wiring.png

Thank you very much - i will try this!!!
Top
pidder
Posts: 5
Joined: Mon 24. Jun 2019 9:47:02

TomasN wrote:Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable.
wiring.png

I tried this an it works!!!!! :D :D

Great job thank you very much for your help!

Regards
Peter
Top
enied
Posts: 107
Joined: Mon 15. Oct 2018 4:19:55

TomasN wrote:Use plus, gnd and signal between Unisens and receiver. And connect signal from receiver to Spirit. GND is already connected by another cable.
wiring.png
Hi TomasN,

does it harm to connect GND ? Currently I have connected it and it works.

Thank you in advance for your feedback.

Best, Eugen
Top
TomasN
Posts: 261
Joined: Sun 23. Mar 2014 12:13:16
Location: Černošice/Praha

Connecting also GND is ok . But single signal wire is enough and simplier.
TDF, TDR, Logo 600SX, Oxy 4 Max @ 3Digi, VBar Neo, Spirit, Grapuner mz-32, mx-20
Top
enied
Posts: 107
Joined: Mon 15. Oct 2018 4:19:55

Thank you !
Top
Post Reply

Return to “Support”