[SOLVED] Rp3-h elrs receiver. No telemetry values.

In case you do not know something or you are not sure, here is the right place for your question.
Post Reply
Mona
Posts: 42
Joined: Wed 15. May 2024 11:00:21

Great, thank you. Looking forward to it.
Top
ZeXx86
Site Admin
Posts: 12782
Joined: Mon 29. Apr 2013 16:06:44
Contact:
Contact ZeXx86

ELRS integration is ready. Anyone interested can get early access.
Spirit System developer
Top
tmura
Posts: 3
Joined: Thu 13. Feb 2025 3:18:44

ELRS integration is ready. Anyone interested can get early access.
Thank you for your assistance.
Where are the earlier versions?
From pc software I can see 3.7.2-r2
Top
ZeXx86
Site Admin
Posts: 12782
Joined: Mon 29. Apr 2013 16:06:44
Contact:
Contact ZeXx86

Please write me private message with serial number of your unit. We will assign new firmware there.
Spirit System developer
Top
ZeXx86
Site Admin
Posts: 12782
Joined: Mon 29. Apr 2013 16:06:44
Contact:
Contact ZeXx86

We assigned firmware to these that sent me a message.

Compatibility with all ELRS receivers should be perfect now while all recent Spirit units have full Spirit integration now. Photos in the attachment below.
Attachments
20250417_123020.jpg
20250417_123001.jpg
20250417_123139.jpg
20250417_123047.jpg
Spirit System developer
Top
tmura
Posts: 3
Joined: Thu 13. Feb 2025 3:18:44

RP3-H telemetry is stable on the bench with 3.7.4.
My setup are below:
- spirit GT
- RP3-H elrs 3.4.3 (250hz/telem ration 1:8)
- RM Boxer / BetaFPV nano TX v2
- HW Platinum 80A V5 (w/DIY telem uni cable)
Pack voltage and current are available without interruption.
(Note: I had to swap the tx/rx pins on GT unit)
Thanks! :D
Top
IFHELI
Posts: 19
Joined: Sun 21. Sep 2014 22:23:28

Still does not work for me. I will have too look at it later tonight.
Top
IFHELI
Posts: 19
Joined: Sun 21. Sep 2014 22:23:28

More trouble now. The Spirit GT will not power up now wired as needed on this firmware. Go back to 3.7.3 and flip the wires it works but no telemetry or integration.
Top
ZeXx86
Site Admin
Posts: 12782
Joined: Mon 29. Apr 2013 16:06:44
Contact:
Contact ZeXx86

Please post photo of how it is wired. I guess there is something wrong since other that tried it with GT with same receiver have no problem.
Maybe you are using some special settings of the receiver?
Spirit System developer
Top
IFHELI
Posts: 19
Joined: Sun 21. Sep 2014 22:23:28

I can load 3.7.3 back into Spirit GT and swap white and green wire back and it works fine (no telemetry / integration as expected). black,red and white wire at Rudder port... green at ail port

I load 3.7.4 into the Spirit GT, swap white and green wires. black, red and green wires at rudder port... white wire at ail port. Rx will boot up.GT does not boot up. HW 80A ESC just beeps. No blue light on GT. Servos have power but will not move. No integration or telemetry. Will not connect to software on computer using USB dongle.

Using Spirit 3.7.0 on TX.

I can unplug wire to Rx and plug back in and it will all boot up just no integration or telemetry. Shut it all off and GT will not boot up again.
Top
Post Reply

Return to “Support”