Page 3 of 4
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 7:03:02
by Bladetip
sampoalphascan wrote:You have to decide what is better for you.
The rescue are always activated only when Gyro Gain is negative.
+
The rescue mode you have to set Function parameter in the software, Stabi tab.
Diagnosis is then in the channel gyro displays HF instead HL.
HF/HL what are these to mean?
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 7:15:33
by sampoalphascan
When activated rescue would be "HF"
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 7:33:56
by Bladetip
Ahh ok thank you.....did you see my post before? I wonder if you might know about that??
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 7:34:11
by sampoalphascan
Bladetip wrote:Ok I think I am starting to understand the basic setup here according to the DX8 settings posted by Thomas.
I do have a few questions though.
So I would use method 1 and this does not use bank switching?? Am I correct? Then the ELE/D/R switch would then be my rescue switch??
Would this affect my flight modes? and how if I went with this setup instead of bank switching.
Oh this is also my equipment I am using on my Trex 500 Pro DFC heli
Hobby wing 100a Platinum Pro ESC (am flying in Governor mode setting also)
Spectrum AR7700 reciever, W/Sat.
Since method 1 says for using a sat I am assuming this is the correct method I should use???
Yes, the method 1) may not be used to switch banks. ELE / D / R activates HOLD who deserts a negative value to the channel gyro, thereby activating the rescue. When activating the rescue must be in diagnostics see "HF".
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 7:42:38
by Bladetip
sampoalphascan wrote:Bladetip wrote:Ok I think I am starting to understand the basic setup here according to the DX8 settings posted by Thomas.
I do have a few questions though.
So I would use method 1 and this does not use bank switching?? Am I correct? Then the ELE/D/R switch would then be my rescue switch??
Would this affect my flight modes? and how if I went with this setup instead of bank switching.
Oh this is also my equipment I am using on my Trex 500 Pro DFC heli
Hobby wing 100a Platinum Pro ESC (am flying in Governor mode setting also)
Spectrum AR7700 reciever, W/Sat.
Since method 1 says for using a sat I am assuming this is the correct method I should use???
Yes, the method 1) may not be used to switch banks. ELE / D / R activates HOLD who deserts a negative value to the channel gyro, thereby activating the rescue. When activating the rescue must be in diagnostics see "HF".
"When activating the rescue must be in diagnostics see "HF". By this you mean I need to go into that page of the Spirit settings in the software to activate rescue??
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 7:46:32
by sampoalphascan
the instructions
"To allow the rescue/stabilisation mode you have to set Function parameter in
the software, Stabi tab."
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 7:53:44
by Bladetip
Ok thank you, one more thing please.....please look at this radio specifically the throttle.....do I need to redo this or something it goes from -98 to +30 or something like that...
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 8:00:54
by sampoalphascan
I do not understand the question. I do not know what is photographed.
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 8:13:19
by sampoalphascan
In your case, starts rescue only gyro gain.
RESCUE
NORMAL
Re: DX8 settings for rescue
Posted: Mon 29. Aug 2016 8:15:55
by Bladetip
sampoalphascan wrote:I do not understand the question. I do not know what is photographed.
There is not picture of my monitor of my radio showing?
My monitor shows at bottom throttle I have -96, and full throttle showing +30. I am wondering how i can get it to read -100 and +100
I am afraid this throws everything out like 0 stick actually not being 0 stick. I don't know how it got this way.
Also I do not have radio set up just yet, I saw this throttle setting and became concerned and am thinking I shouldn't set any rescue up until the throttle setting is resolved