Page 1 of 1
[SOLVED] Geolink v2 missing minumum altitude setting
Posted: Fri 19. Aug 2022 12:14:58
by larspe
I am in the process of installing Geolink 2 with my Spirit Pro. Using Sprit 3.4.1. In the General/Geolink/Aid windows, only maximum altitude is available to be configured. No minimum altitude, which is the setting I need to set for enable a hard deck. See attached screen shot. Appreciate any assitance!
Re: Geolink v2 & Spirit Pro - missing minumum altitude setti
Posted: Fri 19. Aug 2022 12:37:31
by larspe
... and I am in Bank0
Re: Geolink v2 & Spirit Pro - missing minumum altitude setti
Posted: Fri 19. Aug 2022 14:07:05
by Azetof
Hi larspe,
The setting for minimum altitude for Hard Deck will (according to Tomas) probably return due to requests in one of the following Firmware Updates - the way it is right now is actally how its meant to be - you assign a channel to F:rescue(Auto) and the height at which you engage the function is Set as Hard Deck Altitude. ImO a very elegant and practicable solution...
Greetings
Re: Geolink v2 & Spirit Pro - missing minumum altitude setti
Posted: Fri 19. Aug 2022 15:22:30
by larspe
Thanks! Just found the same in the release notes.
Re: Geolink v2 & Spirit Pro - missing minumum altitude setti
Posted: Fri 19. Aug 2022 17:06:52
by larspe
Well - not so fast
Rescue (auto) is not available for the Spirit Pro, only GT/GTR. How do I configure so that hard deck is activated (and deactivated)? Thanks!
Re: Geolink v2 & Spirit Pro - missing minumum altitude setti
Posted: Sat 20. Aug 2022 10:09:40
by Azetof
Oops, musst have overread what Version youre using -
Rescue (Auto) /Hard Deck from the fbl ubit is only supported by gt/gtr since its the first Revision with a built in pressure sensor (=altimeter).
So you can "only" use the geolink function for this (probably wont notice any difference to the pressure sensor Hard Deck..)
See configuration/altitude Limit in the geolink Manual (
http://manual.spirit-system.com/index.p ... tude_Limit)
Sorry to Not being of more help, but i havent used a spirit pro so far, only spirit 2 and gt - spirit developer Tomas (Zexx86) will probably have to step in and answer, hes sick this week (See "limited Support" thread in the Support forum, hell surely answer next week
All the Best,
Re: Geolink v2 & Spirit Pro - missing minumum altitude setti
Posted: Sat 20. Aug 2022 19:33:50
by denis747
The minimum height will be set at the height where you first engage geolink hard deck.
Re: [SOLVED] Geolink v2 missing minumum altitude setting
Posted: Thu 25. Aug 2022 11:13:24
by jasc
so do I need to set geofence and Geolink Altitude to the same channel ?
Re: [SOLVED] Geolink v2 missing minumum altitude setting
Posted: Thu 25. Aug 2022 11:15:59
by ZeXx86
No, this is not needed. You can set it freely so it will be comfortable for you.
Re: [SOLVED] Geolink v2 missing minumum altitude setting
Posted: Thu 25. Aug 2022 13:32:25
by jasc
ZeXx86 wrote:No, this is not needed. You can set it freely so it will be comfortable for you.
That I don't understand
I also noticed min altitude is missing. There is only max altitude. So is min altitude set automatically to height I activate Geofence??