Page 1 of 3
[SOLVED] Spirit2 - fport - No telemetry
Posted: Sun 16. Apr 2023 18:38:06
by jjuk
I have set up a Spirit 2 (v3.5.0) with a r-xsr f.port receiver running ACCST v1.
The spirit 2 is receiving channel information correctly. It's fully operational.
The spirit 2 doesn't seem to be sending any telemetry information back to the radio, also the OpenTx scripts are not loading (because the spirit 2 isn't sending telem back to the radio).
Re: Spirit2 - fport - No telemetry
Posted: Sun 16. Apr 2023 19:18:40
by ZeXx86
Hello,
we have exactly this receiver and it works with F.Port well, including telemetry and integration.
Do you have something else connected to F.Port bus?
Is F.Port receiver type configured in the Spirit unit?
Re: Spirit2 - fport - No telemetry
Posted: Sun 16. Apr 2023 23:23:34
by MegaHz
Make sure you have the connector plugged in the right way. The exact situation happened to me. in ACCST you should be on S.PORT technically
Re: Spirit2 - fport - No telemetry
Posted: Sun 16. Apr 2023 23:44:54
by jjuk
My r-xsr is connected as follows:
https://oscarliang.com/wp-content/uploa ... 24x591.jpg
Code: Select all
Un-inverted smart port -> Spirit 2 ELE/PIT/AIL top pin
RX Power -> Spirit 2 RUD top pin
RX Gnd -> Spirit 2 RUD bottom pin
Receiver is set to "FrSky F.Port"
I have full control, but no telem.
Re: Spirit2 - fport - No telemetry
Posted: Mon 17. Apr 2023 12:58:04
by ZeXx86
Maybe problem is here:
RX Power -> Spirit 2 RUD middle pin
Re: Spirit2 - fport - No telemetry
Posted: Mon 17. Apr 2023 14:32:20
by jjuk
Sorry that was a typo. The power is connected to the centre pin.
Re: Spirit2 - fport - No telemetry
Posted: Mon 17. Apr 2023 14:38:03
by Vector
Did you updated r-xsr with last FW ? And did you put rx in f.port mode?
Re: Spirit2 - fport - No telemetry
Posted: Mon 17. Apr 2023 20:17:35
by jjuk
Here are all the software versions that I'm using:
Spirit 2 v3.5.0, 4ds file attached.
R-XSR:
I'm running RXSR-FPORT_LBT_ACCST_191128.frk from here:
https://www.frsky-rc.com/wp-content/upl ... 191128.zip
The receiver is showing a green and a blue LED, which I believe means green=bound, blue=fport.
Transmitter:
Running OpenTx 2.3.14, and Spirit integration
https://www.spirit-system.com/dl/opentx ... 4.3-en.zip
I have full channel control of the Spirit 2, all channels are working, so the receiver must be outputting f.port to the spirit, but the spirit isn't sending telem to the receiver.
Re: Spirit2 - fport - No telemetry
Posted: Mon 17. Apr 2023 23:25:27
by Vector
Try this ACCST D16 v2.1.0, ACCST D16 v2.1.1(F.Port firmware update only )
GT 3.5 + R-Xsr 2.1.1 LBT and EdgeTX 2.8 integration 3.4.3 everything works great.
Re: Spirit2 - fport - No telemetry
Posted: Mon 17. Apr 2023 23:42:13
by jjuk
Just flashed the transmitter to ACCST v2.1.0, and the r-xsr receiver to "RXSR_ACCST_2.1.1_Fport_LBT.frk."
https://www.frsky-rc.com/wp-content/upl ... v2.1.1.zip
I have full control of the model, but no telem is being sent back to the radio.
